Package Avs-FirmwaresBundle_25.06.02

• AVBx3 version: 5.007

• Update code with the latest functions to manage the new AxC firmware
• Optimization of start-up time
• Bypass of the old method of reading the serial number when (S/N == 0) or (S/N == 0xFFFF)
• - Allows in supervisor mode to force a new S/N on an old firmware core without S/N
• Resolve ASRC management on AVBx3 without matrix
• - AxC-ADSP should be in slot 2 when in ASRC mode
• Fix the change to a new clock source that is not locked
• The lock status of a card with multi sources only reflect the current source...

• AiC-CORE-X-A7-FPGA version: 1.015

• Add the "Mute Slot" capability

• AiC-xCore version: 2.047

• Flash access commands optimization to speed-up firmware update
• Improve security access on some internal registers

• AVBx7 version: 4.028

• Last changes since version 3.006
• - Fixed AxC-ADSP settings when changing mode from ASRC to DSP in a preset
• - Managing the MailBox of Slot 14 if it is available for AVBx display manager
• - Added Mbx_Core_Info Status in Page 0 of slot 14 for AVBx display manager
• - Adding Brightness values in page CSPR of slot 14 for AVBx display manager
• - Added Load/Save functions in Automation
• - Increasing max wait time for Load/Save functions to manage new firmwares
• - Adding CoreX-FPGA MailBox Management for futur AVBx Display inetrface
• - Triggers in automation work on change instead of level for all functions (previously this was only done for Rise/Fall/Change functions)
• - Added management of extended SPI zones when available
• - Address errors are now reported in QOS AxC-MEM
• - SPI transaction optimizations
• - Added timer for inter SPI transaction to avoid unecessary active wait at end of each transaction
• - Management of area with extended memory space (NBPMO > 192)
• - Modified Preset/Scene to managed extended memory space
• - Added the slot15 throughput performance in QOS page for the read write bursts
• - Forces now a clear of old trigger state when the trigger is off.
• - Improved SPI Burst transfers in reading
• - First version 4.xxx with modification of the functions associated with the M0/M4 cores
• - The M0 CORE now manages the network parts (Ethernet, UDP and UPI)
• - The M4 Core now manages the AxC cards (SPI, MailBox, SpiFi, Automation)
• - The management of a Linkscript is now common and shared by the 1st and 2nd startup programs of the M4 core
• - Periodically refresh SR1 cache to update SPI capabilities in case of firmware downgrade without reboot
• - Added Core-FPGA for SR1 refresh and page info for the same reason
• - Management of FPPR command and semaphore in UPI8 and Extended MailBox
• - Add Extended FPPR MailBox flag in Core info Status register
• - Avoid processing a new FPPR Mailbox command while waiting for an FPPR command to complete
• - First implementation of SDR and DDR management
• - Management of the "Wide Area" indicator of the Mailbox. When it is activated, the mailbox accesses the full size zone otherwise only the limited legacy space
• - Management of the UDP UPI16 protocol and Wide Area to access the entire memory space of the areas.
• - For backward compatibility reasons: UPI16 and UPI8 uses the same frame format.
• - The Wide Area flag determines if there is an access to extended space in an area when set or to the limited legacy space when reset.
• - Regardless of the access method (Mailbox, UPI8, ...) the use of the direct access area only gives access to the limited legacy space.
• - Added the SLIM and WIDE mode to area management in Read/Write/T&S/T&R for Legacy/Extended area access
• - Adapted MailBox et UPI8 to use areas in slim or wide mode
• - Management of last version of matrix that can use multiple clusters of 8x slots x 64 channels
• - Changed the management of SR1 and Page_info cache refresh
• - Added Area-Burst mode tests if available during the SPI Speed adjustments at start
• - Changed the typical SPI speeds on A7/S6
• - Added new page in QOS area for additional CoreX LPC statuses with current LED display on front panel
• - Changed SPI clock pin settings to fix AxC-Card-S6 SPI errors on slot4/6 of CoreX-A7
• - Added Led Status for SPI errors detected at start
• - Added Led Fault when GPIO/WCLK is not detected
• - Added specific Auto Test of SPI on all slots
• - Added a new FPPR command parameter to run specific Auto Test of SPI on all slots
• - Fixed bug in recalling/saving scenes/presets when accessing a wide area is required to access all data
• - Optimization of Led driver functions
• - Fixed an issue during a soft reset where the reset was not sent to the board coprocessors in the last slot
• - Set CoreX Status to "discovery" mode on software reset
• - Fixed DMA issues which was introduced in previous version 4.0xx
• - Fixed a bug in Clear Matrix introduced in previous versions 4.0xx. All patches are now cleared including for slots without a card
• - Fixed a bug on AxC-ADSP in ASRC mode introduced in previous versions 4.0xx
• - After a first loop discovery reset the slot where a card was not detected to give a second chance to detect them (i.e. AxC-SWD5G)
• - Added an event area to indicate an IP address change and a Preset modification
• - New IP/MASK address change management with deferred addresses changes that no longer requires a reboot
• - Fixed an issue with AxC card temperature loading/management introduced in version 4.027

• AxC-GPIO-Wclk version: 2.000

• Firmware optimization
• Reorganization of GPI treatment with 2 couples of input voltage threshold (VIL1, VIH1) and (VIL2, VIH2)
• Provides information status of validity for the GPIs with these 2 couples of input voltage threshold

• ALP-AES67-A7 versions: 1.190 / 2.006

• New kernel 1.8.1
• NMOS: add IS-04/05 version to advanced pages
• NMOS: senders/receivers list empty after registry failure with mDNS
• NMOS: prevent users to use web port for NMOS
• fix ICMP for unicast stream
• NMOS: receiver label not updated until source is patched
• NMOS: device/node properties inconsistent at startup
• NMOS: improved registry failover resilience
• prevent from restarting if IP is renewed when FW updating
• Device remote command not acknowledged with command reboot
• network vulnerabilities: disable ICMP timestamp responses
• support for create/listen sources/sinks in the multicast range 224.x.x.x and x.x.x.255
• Remove ASIO clock RAVENNA stream reservation limitation
• audio mute when ST-2022 sink stops receiving on secondary port on 3-NIC devices on some configurations
• fix on allowing custom I2S module to have 0 inputs or 0 outputs
• Use default web service.
• Improve audio bloc to allow asymetric driver (Play without Record and opposite)

• ALP-DANTE-A7 versions: 1.190 / 11.014

• UPI8 Evolution
• Improve audio bloc to allow asymetric driver (Play without Record and opposite)

• AVDT-BOB-AE4IO versions: 3.021 / 1.005

• Fix disconnection with several web BOB page open
• New gain management db R68-2000 / dBu / dB legacy

• AVW-DT4I versions: 2.112 / 5.006

• Fix: ADC init based on register detection.
• New: Add internal IHM register in AxC-Mem Err&Tst page.
• New: Disable LED dimmer mode in active mode.
• New: Allow Bluetooth activation with long push on the button.
• Fix: Bluetooth disconnection status was not working in some very case.

• AxC-ADSP versions: 2.011 / 2.016

• New: Support UPI8 protocol.
• New: New mailbox protocol acess and exteneded mailbox to 8 page buffer.
• Fix: New IP stack version. Improvement of connection reliabilty.
• Fix: new save, load internal mechanism.
• Fix: Dynamic pagination of AxC-Mem of LPC from FPGA.
• Fix: Update webservice: fix scene display of ADSP.
• Fix: Channel label load / saved correctly.
• Change the Vumeter lower limit from -48dB to -72dB

• AxC-AES67-A7 versions: 1.020 / 1.036

• Fix internal IT management to avoid flooding on burst write
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load
• Change some internal I/O number registers to read-only
• Added audio router management with default initialization.
• Correction of channel <=> router <=> application naming
• Added blocking of sample rate configuration from the web interface.
• Change the Vumeter lower limit from -48dB to -72dB

• AxC-AT32IO version: 4.015

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-AVB versions: 2.099 / 2.039 / 8.072

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-AE8M version: 2.023

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-AS16MO-V2 version: 1.018

• Change the In/Out/Global mute behaviour to ensure signal is still routed to vumeter when device muted

• AxC-AX4M version: 4.025

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-AX4I version: 7.023

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-CN32IO version: 2.020

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-DANTE versions: 2.056 / 10.062

• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load
• Change the Brooklyn reset system to avoid some blocking issues
• Add remote NXAMP device monitoring ( Brooklyn3 )
• Fix abusive lock
• Change the Vumeter lower limit from -48dB to -72dB

• AxC-DANTE-A7 versions: 1.015 / 10.062

• Bug fix on HA-Remote configuration mode issues (internal Brooklyn reset management).
• Extension of CSPR pages number.
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load
• Add remote NXAMP device monitoring ( Brooklyn3 )
• Fix Factory Reset
• Fix abusive lock
• Change the Vumeter lower limit from -48dB to -72dB

• AxC-DX8I version: 6.030

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load

• AxC-ES100 version: 27.012

• Bug fix on PID that could disable the ASIO capability

• AxC-GPIO16 version: 2.002

• Firmware optimization
• Reorganization of GPI treatment with 2 couples of input voltage threshold (VIL1, VIH1) and (VIL2, VIH2)
• Provides information status of validity for the GPIs with these 2 couples of input voltage threshold
• Provides relay activation status for GPOs

• AxC-MADI versions: 12.019 / 1.038

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load
• Change the Vumeter lower limit from -48dB to -72dB

• AxC-MADI_SFP versions: 12.019 / 1.038

• Change some internal I/O number registers to read-only
• DMA page is no longer loaded (when exists) to avoid rare cases of undesired registers writes at load
• Change the Vumeter lower limit from -48dB to -72dB

• AxC-SWD5G version: 1.010